- 2005 honda autotrax f 12x for sale manuals#
- 2005 honda autotrax f 12x for sale install#
- 2005 honda autotrax f 12x for sale manual#
After washing the watercraft, consider using a commercially-available spray cleaner/polish or quality fiberglass marine polish wax to finish the job.Honda strongly recommends that any body damage (e.g., cuts, scratches, holes) be repaired by a qualified boat repair facility.The bodywork is made up of two basic materials: the hull and deck are FRP with a Gel coat finish and the hood, mirrors and upper covers are made of plastic.This section covers removal and installation of the body covers.These products will damage the gel-coat finish. Never clean fiberglass and plastic components with strong chemicals or cleaning detergents. However, if the manifold surface temperature (MST) switch and/or the ECT sensor detects an engine temperature above 95☌ (203☏), the fail-safe function stops the engine. If the engine coolant temperature (ECT) sensor detects an engine temperature above 85☌ (185☏), the fail-safe function allows the engine to continue to operate. The watercraft incorporates a fail-safe function in the event that the engine overheats. However, if the low oil pressure switch detects an engine oil pressure below 20 kPa (0.2, kg/cm2, 3 psi), the fail-safe function stops the engine. If the high oil pressure switch detects an engine oil pressure below 216 kPa (2.2 kg/cm2, 31 psi), the engine control module lights the oil pressure warning light and limits the engine speed to 3,000 rpm to prevent engine damage. The watercraft incorporates a fail-safe function in the event that the engine oil pressure drops. This dry sump design incorporates an oil cooler that lowers the oil temperature. This engine can be positioned lower than conventional engines, because the oil is not stored in the lower portion of the crankcase. The scavenge pump transfers oil from the sump to the oil tank. The feed pump draws oil from the oil tank and supplies it to various engine components. This dry sump system consists of an external oil tank on the front of the engine, and a dual rotor oil pump (scavenge and feed) located within the oil tank. Route all electrical wires as shown in the Cable and Harness Routing (page 1-31 or 1-52). After reassembly, check all parts for proper installation and operation.Ĩ. Lubricate any sliding surfaces before reassembly.ħ. Clean parts in cleaning solvent upon disassembly. Then tighten to the specified torque diagonally in incremental steps unless a particular sequence is specified.Ħ. When tightening bolts or nuts, begin with the larger diameter or inner bolt first.
2005 honda autotrax f 12x for sale install#
Install new gaskets, O-rings, cotter pins, and lock plates when reassembling.ĥ. Metric bolts, nuts and screws are not interchangeable with English fasteners.Ĥ. Use only metric tools when servicing the watercraft. Use the special tools designed for this product to avoid damage and incorrect assembly.ģ. Parts that do not meet Honda's design specifications may cause damage to the watercraft.Ģ. Use genuine Honda or Honda-recommended parts and lubricants or their equivalents.
2005 honda autotrax f 12x for sale manual#
(Chapters may differ in each manual depending on year and model)ġ. TYPICAL CHAPTERS IN A HONDA AQUATRAX SERVICE MANUAL: Improper repair may result in injury to the mechanic and may render the engine unsafe for the watercraft operator and passengers. Never attempt to perform any work with out the assistance of a service manual.Īpprentice mechanics or do-it-yourself mechanics that don’t have the proper tools and equipment may or may not be able to properly perform the services described in this manual.
Persons without such knowledge and skills should attempt with caution to service any component or engine by relying on this manual only.
2005 honda autotrax f 12x for sale manuals#
These manuals are intended for use by technicians who already possess the basic knowledge and skills to service a personal watercraft motors and components.Illustrations in these manuals are used to show the basic principles of operation and work procedures of the actual personal watercraft and components in exact detail.These manuals and the actual PWC personal water craft. If a modification has been made since then, differences may exist between the content of These manuals have been prepared using the latest information available at the time of publication.Read and refer to the other sections in this manual for information regarding proper inspection and service procedures. Please read the GENERAL INFORMATION section to familiarize yourself with basic information concerning your personal watercraft PWC in the manual. General knowledge information is not included. These manuals contains an introductory description on and procedures for the inspection, service and overhaul of its main components.